UD Trading Pty Ltd company logo

Cyanuric Acid

UD Trading supplies cyanuric acid (isocyanuric acid, pool chlorine stabiliser, CAS 108-80-5) at 98.5% minimum purity as a white crystalline powder to pool shops and pool-chemical blenders, pool builders and service companies, aquatic centres, councils, water-treatment users and chemical manufacturers across Australia. Orders are dispatched from our warehouses across Australia to Brisbane, the Gold Coast, Sydney, Melbourne, Perth, Adelaide, Darwin, Townsville and regional centres in 25 kg bags, with a Certificate of Analysis for every batch under our ISO 9001:2015 quality system.

Cyanuric Acid at a glance

Chemical NameCyanuric Acid
Chemical FormulaC3H3N3O3
Other Names1,3,5-Triazine-2,4,6-triol, Isocyanuric Acid, Pool Stabiliser
CAS No108-80-5

Pack sizes and how to order

PackNet weightTypical buyer
25 kg bag with PE liner25 kg (40 per pallet)Pool shops, service technicians, aquatic centres
Pallet of 25 kg bags, shrink-wrapped1,000 kgPool-chemical blenders and distributors
Bulk bag (FIBC, jumbo bag)1,000 kgPlants, mines, contractors, scheduled supply
Full container load (FCL)20–24 tScheduled contract supply through the swimming season

Pricing is quoted per order, delivered, usually within one business day of your enquiry; trade and pallet pricing is available for pool shops and blenders. Contract pricing is available for scheduled volumes. Lead time depends on quantity: smaller orders are dispatched from our warehouses across Australia; larger volumes are scheduled to order; full container loads typically take 30 to 60 days. Request a quote or call +61 7 3040 7298.

Cyanuric Acid specification

Cyanuric acid is specified on purity, moisture, ammeline plus ammelide content and pH. Low ammeline and ammelide matter because these by-products dissolve poorly and cloud pool water.

ParameterSpecification
AppearanceWhite crystalline powder
Cyanuric acid≥ 98.5 %
Moisture≤ 0.5 %
Ammeline + ammelide≤ 1.0 %
pH (1%)3.5 – 4.5
Heavy metals (as Pb)≤ 10 mg/kg

Acceptance limits from UD Trading’s approved specification. Actual results for each batch are reported on the Certificate of Analysis.

Physical data: C₃H₃N₃O₃, molar mass 129.07 g/mol; solubility only about 2.7 g/L at 25 °C, so it dissolves slowly and is best added through the skimmer or pre-dissolved in warm water; a saturated solution has pH about 4; thermally stable to above 300 °C; it is not consumed in the pool and leaves only by dilution, backwashing or splash-out; 1 kg raises the cyanuric acid level of 10,000 L by 100 mg/L.

Stabiliser, trichlor or dichlor: which to buy

PropertyCyanuric acid (this product)Trichlor tabletsDichlor granules
What it addsStabiliser only; no chlorineChlorine 90% plus about 0.55 kg of CYA per kgChlorine 56–62% plus about 0.5–0.6 kg of CYA per kg
Effect on pHSlightly lowersLowers strongly (pH 2.8)Near neutral
When to usePools sanitised with liquid chlorine, salt chlorinators or cal hypo that need UV protectionContinuous feed where stabiliser creep is managedShock and start-up
RiskOver-stabilising if dosed with stabilised chlorineCYA build-up over a seasonCYA build-up over a season

How much cyanuric acid do you need: worked examples

Dose (kg) = pool volume (L) × desired increase (mg/L) ÷ 1,000,000. Target 30–50 mg/L for liquid-chlorine and cal-hypo pools, 50–80 mg/L for salt-chlorinator pools, never above 100 mg/L; keep free chlorine at 7.5% or more of the cyanuric acid reading to avoid chlorine lock.

  • New 50,000 L salt pool to 60 mg/L. 50,000 × 60 ÷ 1,000,000 = 3.0 kg. Add 1 kg at a time through the skimmer with the pump running, or pre-dissolve in a bucket of warm water; retest after 48 hours because it dissolves slowly.
  • Top-up after winter dilution. A 60,000 L pool reading 20 mg/L with a 40 mg/L target needs 60,000 × 20 ÷ 1,000,000 = 1.2 kg.
  • Aquatic centre, 1,000,000 L, to 30 mg/L. 30 kg, a little over one bag; stage it over two days and keep free chlorine above 2.3 mg/L (7.5% of 30).
  • Chlorine saving. Unstabilised chlorine loses roughly half its residual to sunlight in 1–2 hours; at 30–50 mg/L cyanuric acid the loss rate falls by 5–10 times, which typically halves the liquid chlorine or chlorinator run-time needed in summer.
  • Lowering a high reading. Cyanuric acid is removed only by dilution: dropping 120 mg/L to 60 mg/L means replacing half the pool water, or using a reverse-osmosis service.

What Cyanuric Acid is used for

  • Pools and spas. Chlorine stabiliser that shields hypochlorous acid from UV in outdoor pools; pairs with pool salt, sodium bicarbonate, soda ash and hydrochloric acid for water balance.
  • Pool-chemical manufacture. Feedstock for trichloroisocyanuric acid and sodium dichloroisocyanurate, and for stabilised chlorine blends.
  • Water and sanitising. Stabilised chlorine for water tanks, cooling systems and sanitiser tablets.
  • Chemical manufacture. Intermediate for herbicides, cross-linkers, flame retardants and specialty polymers.

Handling and storage

Cyanuric acid is not classified as dangerous goods for transport and is of low toxicity, but the powder irritates eyes and airways: use a dust mask and eye protection when tipping bags. Store sealed, dry and off the ground away from strong oxidisers and strong bases. Never mix dry chlorine products with cyanuric acid or other chemicals in the same container. Always read the Safety Data Sheet before use.

Why buy Cyanuric Acid from UD Trading

Pool shops and blenders need stabiliser that dissolves clean and arrives before the season does. Every batch is released against our specification for purity, moisture and ammeline plus ammelide under our ISO 9001:2015 quality system, and we hold stock in multiple Australian warehouses for pallet orders. Browse our water treatment chemicals, or contact our team for a quote. Chemical identity reference: CAS 108-80-5 on CAS Common Chemistry.

Cyanuric Acid FAQ

What purity is your cyanuric acid?

98.5% minimum, moisture ≤ 0.5%, ammeline plus ammelide ≤ 1.0%, reported on the batch COA.

What pack sizes do you supply?

25 kg bags, 1,000 kg pallets of 25 kg bags and full container loads.

How much raises my pool by 10 mg/L?

100 g per 10,000 L; a 50,000 L pool needs 500 g for every 10 mg/L.

Is cyanuric acid dangerous goods?

No. It is not classified as dangerous goods for transport. Avoid dust and follow the SDS.

Why does my stabiliser level keep rising?

Trichlor and dichlor add cyanuric acid with every dose. Switch to liquid chlorine, a salt chlorinator or cal hypo once the reading passes 50–80 mg/L.

What is the lead time?

It depends on quantity. Smaller orders are dispatched from our warehouses across Australia; larger volumes are scheduled to order; a full container load typically takes 30 to 60 days.

Do you sell to pool shops and blenders?

Yes. Trade, pallet and seasonal contract pricing is available, with delivery Australia-wide by road freight.

Do you offer contract pricing for scheduled volumes?

Yes. Fixed-period contract pricing is available for scheduled pallet and container quantities through the swimming season.

Product Documents

Download Specification Download SDS

A Certificate of Analysis (COA) is supplied with every batch.

Contact UD Trading for Cyanuric Acid

Contact us for pricing, availability and documentation for Cyanuric Acid. Call 07 3040 7298 or email sales@udtrading.com.au.

Request a Quote

Ready to Elevate Your Operations?

Connect with our industry experts and unlock your business potential.

Enquire Today

Locations

UD Trading service locations across Australia