UD Trading Pty Ltd company logo

Poly Aluminium Chloride (PAC)

UD Trading supplies poly aluminium chloride (PAC) powder (CAS 1327-41-9) with at least 28% alumina (Al₂O₃), also sold as our Strong Clarifier, to councils and water utilities, wastewater plants, pool and spa suppliers, mines, food processors, paper and textile plants across Australia. Orders are dispatched from our warehouses across Australia to Brisbane, Sydney, Melbourne, Perth, Adelaide, Darwin, Townsville and regional water plants, with a Certificate of Analysis for every batch under our ISO 9001:2015 quality system.

Poly Aluminium Chloride at a glance

Chemical NamePoly Aluminium Chloride
Chemical FormulaAln(OH)mCl(3n-m)
Other NamesPAC, Polyaluminium Chloride
CAS No1327-41-9

Pack sizes and how to order

PackNet weightTypical buyer
25 kg bag with PE liner25 kg (40 per pallet)Pool shops, small water plants, food and industrial sites
Pallet of 25 kg bags, shrink-wrapped1,000 kgCouncils, regional utilities, distributors
Bulk bag (FIBC)1,000 kgLarge plants with make-up systems
Full container load (FCL)20–24 tScheduled contract supply

Pricing is quoted per order, delivered, usually within one business day of your enquiry. Contract pricing is available for scheduled volumes. Lead time depends on quantity: smaller orders are dispatched from our warehouses across Australia; larger volumes are scheduled to order; full container loads typically take 30 to 60 days. Request a quote or call +61 7 3040 7298.

Poly Aluminium Chloride specification

PAC is specified on alumina content, basicity, insolubles and pH. Alumina sets the dose; basicity (the degree of pre-hydrolysis) sets how much alkalinity the coagulant consumes and how well it works in cold or low-alkalinity water.

ParameterSpecification
AppearancePale yellow to yellow powder
Alumina (Al2O3)≥ 28.0 %
Basicity30.0 – 95.0 %
Water-insoluble matter≤ 0.4 %
pH (10 g/L solution)3.5 – 5.0

Acceptance limits from UD Trading’s approved specification. Actual results for each batch are reported on the Certificate of Analysis.

Physical data: general formula [Al₂(OH)ₙCl₆₋ₙ]ₘ; 28% Al₂O₃ corresponds to about 14.8% aluminium by mass; bulk density about 0.7–0.9 g/mL; fully soluble, giving a clear pale-yellow solution; a 10 g/L solution has pH 3.5–5.0; 1 kg of 28% PAC powder carries the same alumina as about 1.65 kg of dry alum (17% Al₂O₃) or 2.8 kg of 10% Al₂O₃ liquid PAC; effective from pH 5 to 9 and in cold water where alum slows down.

PAC or alum: which coagulant to buy

PropertyPAC powder 28% Al₂O₃ (this product)Aluminium sulphate (alum) 17% Al₂O₃
Dose for the same turbidityBaselineTypically 1.5–2.5× more product
Alkalinity consumedLow (pre-hydrolysed); little or no lime or soda ash neededAbout 0.5 mg/L alkalinity per mg/L alum; often needs lime or soda ash
Working pH and temperaturepH 5–9, works in cold waterpH 6–7.5, slower below 10 °C
Sludge volume20–30% lessHigher, wetter sludge
Residual aluminiumLower at correct doseHigher if pH drifts
Best suited toDrinking water, cold or low-alkalinity sources, pools, wastewater polishingLow-cost bulk treatment with good alkalinity; see aluminium sulphate

How much PAC do you need: worked examples

Set the dose by jar test; typical PAC powder doses are 5–30 mg/L for drinking water and 20–100 mg/L for wastewater.

  • Drinking water plant, 10 ML/day at 15 mg/L. 10,000 m³ × 15 g/m³ = 150 kg of PAC powder a day, six bags, about 4.5 t a month. The same job with alum at a typical 30 mg/L would use 300 kg a day plus 150 mg/L-equivalent of alkalinity correction.
  • Making a 10% w/v stock solution. Dissolve 100 kg of PAC powder in water to 1,000 L. A dosing pump delivering 15 mg/L to 400 m³/h needs 400 × 15 = 6,000 g/h, which is 60 L/h of 10% stock.
  • Wastewater phosphorus removal. Each mg/L of phosphorus removed needs roughly 2–3 moles of Al per mole of P in practice, about 1.5–2.5 mg of Al, or 10–17 mg/L of 28% PAC. Removing 4 mg/L P from 5 ML/day at 15 mg PAC per mg P takes 5,000 × 4 × 15 ÷ 1,000 = 300 kg a day, 12 bags.
  • Pool and spa clarifying. For cloudy pool water after storms or algae treatment, dissolve PAC in a bucket and add at about 10–20 g per 10,000 L with the filter running, then backwash when pressure rises. Pair with sodium hypochlorite for sanitising and sodium bicarbonate to hold alkalinity.
  • Alkalinity check. Raw water below about 30 mg/L alkalinity still benefits from a small soda ash or hydrated lime dose so floc forms quickly; jar-test with and without.

What Poly Aluminium Chloride is used for

  • Drinking water. Primary coagulant for turbidity, colour, natural organic matter and algae removal before filtration, often followed by activated carbon for taste and odour.
  • Wastewater and sewage. Chemical phosphorus removal, enhanced primary treatment, sludge thickening and lagoon polishing.
  • Pools, spas and aquatic centres. Flocculant and clarifier (Strong Clarifier) for cloudy water and filter aid.
  • Mining and industry. Tailings and process-water clarification, paper sizing and retention, textile and dye effluent, oil and grease removal.
  • Food and beverage. Effluent treatment and process water clarification.

Handling and storage

PAC powder is acidic and can irritate the eyes and skin: wear eye protection and gloves, avoid dust and use a P2 mask when tipping bags. It is not classified as dangerous goods for transport under the ADG Code. Store sealed, dry and off the ground; the powder is hygroscopic and cakes if left open. Make up solutions in plastic or lined tanks, not bare mild steel. Always read the Safety Data Sheet before use.

Why buy Poly Aluminium Chloride from UD Trading

A coagulant that misses its alumina or basicity number shows up as turbidity breakthrough and wasted dose. Every batch is released against our specification under our ISO 9001:2015 quality system, and we hold stock in multiple Australian warehouses so plants are not caught short in the wet season. Browse our water treatment chemicals, or contact our team for a quote. Chemical identity reference: CAS 1327-41-9 on CAS Common Chemistry.

Poly Aluminium Chloride FAQ

What grade is your PAC?

Powder with at least 28% Al₂O₃, basicity 30–95%, insolubles ≤ 0.4%, reported on the batch COA. It is the same product as our Strong Clarifier.

What pack sizes do you supply?

25 kg bags, 1,000 kg pallets of 25 kg bags, bulk bags and full container loads.

How much PAC replaces my alum dose?

On alumina content 1 kg of 28% PAC powder equals about 1.65 kg of dry alum, and in practice PAC achieves the same turbidity at 40–60% of the alum product dose. Confirm by jar test.

Is PAC dangerous goods?

No. PAC powder is not classified as dangerous goods for transport, but it is acidic and irritant. Follow the SDS.

Can it be used in swimming pools?

Yes. It is widely used as a pool clarifier and flocculant; dose 10–20 g per 10,000 L and backwash the filter afterwards.

What is the lead time?

It depends on quantity. Smaller orders are dispatched from our warehouses across Australia; larger volumes are scheduled to order; a full container load typically takes 30 to 60 days.

Do you deliver to regional water plants?

Yes. We deliver Australia-wide by road and rail freight, with freight quoted per consignment.

Do you offer contract pricing for scheduled volumes?

Yes. Fixed-period contract pricing is available for scheduled pallet and container quantities.

Product Documents

Download Specification Download SDS

A Certificate of Analysis (COA) is supplied with every batch.

Contact UD Trading for Poly Aluminium Chloride (PAC)

Contact us for pricing, availability and documentation for Poly Aluminium Chloride (PAC). Call 07 3040 7298 or email sales@udtrading.com.au.

Request a Quote

Ready to Elevate Your Operations?

Connect with our industry experts and unlock your business potential.

Enquire Today

Locations

UD Trading service locations across Australia