UD Trading Pty Ltd company logo

Glutaraldehyde

UD Trading supplies glutaraldehyde 50% (pentanedial, CAS 111-30-8) in IBCs and drums to oil and gas operators and well-service companies, water-treatment and cooling-tower contractors, pipeline and hydrotest contractors, mines, leather tanners and industrial users across Australia. Orders are dispatched from our warehouses across Australia to Brisbane, Roma, Moomba, Perth, Dampier, Darwin, Sydney, Melbourne and regional centres, with a Certificate of Analysis for every batch under our ISO 9001:2015 quality system.

Glutaraldehyde at a glance

Chemical NameGlutaraldehyde
Chemical FormulaC₅H₈O₂
Other NamesPentanedial, Glutardialdehyde Biocide
CAS No111-30-8

Pack sizes and how to order

PackNet quantityTypical buyer
20 L drumAbout 23 kgTrials, laboratories, workshops, small plants
HDPE drum200 L (about 226 kg)Cooling-tower contractors, tanneries, small sites
IBC1,000 L (about 1,130 kg)Well-service crews, frac water treatment, pipeline hydrotests
Scheduled contract supplyProgram volumesOperators with continuous or campaign biocide programs

Pricing is quoted per order, delivered, usually within one business day of your enquiry; IBCs are supplied on a deposit or exchange basis. Contract pricing is available for scheduled volumes. Lead time depends on quantity: drum and IBC orders are dispatched from our warehouses across Australia; larger volumes are scheduled to order; full container loads typically take 30 to 60 days. Request a quote or call +61 7 3040 7298.

Glutaraldehyde specification

Glutaraldehyde is specified on assay, pH, methanol content and specific gravity. Assay sets the dose; the acidic as-supplied pH gives storage stability; low methanol matters for flash point and for sites with vapour limits.

ParameterSpecification
AppearanceColourless to pale yellow liquid
Glutaraldehyde49 – 51 %
pH3.0 – 4.5
Methanol≤ 5 %
Specific gravity (20 °C)1.13 – 1.14

Acceptance limits from UD Trading’s approved specification. Actual results for each batch are reported on the Certificate of Analysis.

Physical data: molar mass 100.12 g/mol; the 50% solution has a density of 1.13 kg/L, so each litre contains about 565 g of active glutaraldehyde; fully miscible with water; pH 3.0–4.5 as supplied, where it is stable for about two years below 30 °C; biocidal activity rises as pH is raised to 7–8.5 in use, but alkaline solutions polymerise within days, so activate only what you will use; it is a broad-spectrum, fast-acting biocide that cross-links the proteins of bacteria, sulphate-reducing bacteria, fungi and algae, is compatible with most oilfield additives, and is deactivated by ammonia, primary amines and bisulphite.

Glutaraldehyde, THPS or quats: which biocide to buy

PropertyGlutaraldehyde 50% (this product)THPS 75%Quaternary ammonium
Speed of killFast, broad spectrum, works in brines and sour systemsFast, also dissolves iron sulphideSlower; surfactant action
Environmental fateBiodegrades in daysOxidises to low-toxicity phosphatePersistent, adsorbs to solids
CompatibilityNot with ammonia, amines, bisulphite oxygen scavengersNot with oxidisers or high pHNot with anionic polymers
Typical active dose50–250 mg/L continuous; 500–1,000 mg/L slug50–150 mg/L10–50 mg/L
See alsoTHPS 75%benzalkonium chloride

How much glutaraldehyde do you need: worked examples

Volume of 50% product (L) = water volume (m³) × active dose (mg/L) ÷ 565.

  • Frac or completion water treatment. 100–250 mg/L active to stop sulphate-reducing bacteria souring the formation. Treating 1,000 m³ of frac water at 200 mg/L needs 200 kg of active, which is 1,000 × 200 ÷ 565 = 354 L of 50% product, about a third of an IBC.
  • Pipeline hydrotest water. 50–100 mg/L active with an oxygen scavenger (choose a non-bisulphite scavenger, or dose the biocide first). A 10,000 m³ test at 100 mg/L takes 1,770 L, nearly two IBCs.
  • Cooling-tower slug dose. 100–200 mg/L active weekly, alternated with an oxidising biocide. A 500 m³ system at 150 mg/L takes 133 L of 50% product per slug.
  • Drilling fluid preservation. 250–500 mg/L active to protect starch and xanthan in water-based muds; a 100 m³ system at 300 mg/L takes 53 L, repeated as the mud is diluted.
  • Neutralising residual before discharge. Sodium bisulphite reacts with glutaraldehyde at about 2.1 kg per kg of active; neutralising 50 kg of residual active in a test-water discharge needs about 105 kg of sodium bisulphite (not sodium bisulphate, which is an acid salt), with a 10% excess and pH check.

What Glutaraldehyde is used for

  • Oil and gas. Biocide for frac and completion water, injection water, drilling fluids, pipelines and storage tanks, controlling souring, corrosion and biofouling, alongside our oilfield chemicals.
  • Industrial water treatment. Cooling towers, closed loops, membrane and reverse-osmosis cleaning, paper-mill slime control.
  • Mining. Process-water and tailings biocide and hydrotest preservation.
  • Leather and industrial. Tanning agent, cross-linker for proteins and resins, embalming and histology fixative.
  • Disinfection. Cold sterilant for equipment and surfaces where a registered product and protocol apply.

Handling and storage

Glutaraldehyde is toxic and can cause severe eye damage, skin sensitisation and asthma from vapour; it is classified as dangerous goods for transport: UN 2922, Class 8 with subsidiary risk 6.1, Packing Group III. Use closed dosing systems or good ventilation, wear nitrile or butyl gloves, goggles and a face shield, and keep workplace vapour below 0.05 ppm. Store in sealed original containers below 30 °C, out of sunlight and away from alkalis, amines, oxidisers and oxygen scavengers; do not store activated (alkaline) solutions. Always read the Safety Data Sheet before use.

Why buy Glutaraldehyde from UD Trading

Every batch is released against our specification for assay, pH, methanol and density under our ISO 9001:2015 quality system, we ship as Class 8 (6.1) dangerous goods with correct documentation, and we hold stock in multiple Australian warehouses close to the main drilling supply bases. Browse our drilling and oilfield chemicals and water treatment chemicals, or contact our team for a quote. Chemical identity reference: CAS 111-30-8 on CAS Common Chemistry.

Glutaraldehyde FAQ

What strength is your glutaraldehyde?

49–51% w/w, pH 3.0–4.5, methanol ≤ 5%, specific gravity 1.13–1.14, reported on the batch COA.

What pack sizes do you supply?

200 L drums and 1,000 L IBCs, with program contract supply for continuous users.

Is glutaraldehyde dangerous goods?

Yes. UN 2922, Class 8 corrosive with subsidiary risk 6.1 (toxic), Packing Group III. We ship with the correct DG documentation and SDS.

How much do I dose for frac water?

100–250 mg/L active, which is 180–440 L of 50% product per 1,000 m³ of water; higher doses for sour or high-bacteria source water.

Can I use it with my oxygen scavenger?

Not with bisulphite or ammonium-based scavengers, which destroy it. Dose the biocide first and allow contact time, or use a compatible scavenger.

What is the lead time?

Drum and IBC orders are dispatched from our warehouses across Australia; larger volumes are scheduled to order; full container loads typically take 30 to 60 days.

Do you deliver to drilling supply bases?

Yes. We deliver Australia-wide by DG-licensed road and rail freight, including Roma, Moomba, Dampier and Darwin, with freight quoted per consignment.

Do you offer contract pricing for scheduled volumes?

Yes. Fixed-period contract pricing is available for scheduled drum and IBC volumes and campaign programs.

Product Documents

Download Specification Download SDS

A Certificate of Analysis (COA) is supplied with every batch.

Contact UD Trading for Glutaraldehyde

Contact us for pricing, availability and documentation for Glutaraldehyde. Call 07 3040 7298 or email sales@udtrading.com.au.

Request a Quote

Ready to Elevate Your Operations?

Connect with our industry experts and unlock your business potential.

Enquire Today

Locations

UD Trading service locations across Australia