UD Trading Pty Ltd company logo

Zinc Oxide

UD Trading supplies zinc oxide (ZnO, CAS 1314-13-2) of at least 99.5% purity as a white to pale yellow powder to rubber compounders, ceramic and glass makers, paint and coatings manufacturers, fertiliser blenders and chemical producers across Australia. Orders are dispatched from our warehouses across Australia to Brisbane, Sydney, Melbourne, Perth, Adelaide and regional centres in 25 kg bags, with a Certificate of Analysis for every batch under our ISO 9001:2015 quality system.

Zinc Oxide at a glance

Chemical NameZinc Oxide
Chemical FormulaZnO
Other NamesCalamine, Zinc White
CAS No1314-13-2

Pack sizes and how to order

PackNet weightTypical buyer
25 kg bag with PE liner25 kg (40 per pallet)Rubber, ceramics, paint and chemical plants
Pallet of 25 kg bags, shrink-wrapped1,000 kgCompounders, fertiliser blenders, distributors
Jumbo bag (FIBC)1,000 kgLarge plants
Full container load (FCL)20–24 tScheduled contract supply

Pricing is quoted per order, delivered, usually within one business day of your enquiry. Contract pricing is available for scheduled volumes. Lead time depends on quantity: smaller orders are dispatched from our warehouses across Australia; larger volumes are scheduled to order; full container loads typically take 30 to 60 days. Request a quote or call +61 7 3040 7298.

Zinc Oxide specification

Zinc oxide is specified on purity, loss on ignition, lead and cadmium, the four numbers that decide whether a lot is fit for rubber, glaze or feed and fertiliser use.

ParameterSpecification
AppearanceWhite to pale yellow powder
Zinc oxide (ZnO)≥ 99.5 %
Loss on ignition≤ 0.3 %
Lead≤ 20 mg/kg
Cadmium≤ 5 mg/kg

Acceptance limits from UD Trading’s approved specification. Actual results for each batch are reported on the Certificate of Analysis.

Physical data: molar mass 81.38 g/mol; zinc content 80.3% by mass (65.38 ÷ 81.38); density 5.61 g/cm³; melting point about 1,975 °C; practically insoluble in water (about 1.6 mg/L) but soluble in acids and strong alkalis (amphoteric); refractive index 2.0; absorbs UV below about 375 nm; typical BET surface area of this grade 3–6 m²/g.

Which grade of zinc oxide do you need

UseWhat mattersTypical dose
Rubber and tyre compoundsPurity ≥ 99.5%, low lead, consistent particle size for dispersion3–5 phr with 1–2 phr stearic acid
Ceramic glazes and fritsLow loss on ignition, low iron for colour2–10% of the glaze batch
Paints and coatingsWhiteness, UV absorption, mildew resistance5–15% of pigment loading
Fertiliser and trace-element blendsZinc content 80.3%, cadmium ≤ 5 mg/kgSet by soil test; see worked example
Chemical manufacturePurity and heavy metalsStoichiometric

How much zinc oxide do you need: worked examples

  • Rubber compound at 5 phr. Doses are parts per hundred of rubber. A 500 kg batch containing 250 kg of polymer needs 5 ÷ 100 × 250 = 12.5 kg of zinc oxide, half a bag.
  • Zinc for fertiliser blends. 1 kg of 99.5% zinc oxide carries 0.80 kg of zinc, against 0.227 kg in zinc sulphate heptahydrate (ZnSO₄·7H₂O, 22.7% Zn). To add 2 kg of Zn per hectare across 500 ha (1,000 kg Zn) you need 1,000 ÷ 0.80 = 1,250 kg of zinc oxide, or 50 bags, versus 4,400 kg of zinc sulphate.
  • Making zinc sulphate solution. ZnO + H₂SO₄ → ZnSO₄ + H₂O. 81.4 g of zinc oxide reacts with 98.1 g of sulphuric acid (100% basis), so 1 kg of zinc oxide needs 1.21 kg of 100% acid, or 1.23 kg (0.67 L) of 98% sulphuric acid. The reaction is exothermic: add oxide to dilute acid slowly.
  • Glaze batch. A 50 kg glaze at 6% zinc oxide needs 3 kg; weigh to ±10 g because zinc oxide shifts glaze melt and colour response.

What Zinc Oxide is used for

  • Rubber vulcanisation. The main activator for sulphur curing of tyres, conveyor belts, hoses and moulded rubber goods, improving cure rate, modulus and heat resistance.
  • Ceramics and glass. A flux and opacifier in glazes, frits and specialty glass that widens the firing range and improves gloss.
  • Paints and coatings. A white pigment with UV absorption and mould and mildew resistance in exterior and marine coatings.
  • Agriculture and animal nutrition. A concentrated zinc source for granular fertiliser coatings, foliar and trace-element blends; feed-grade supply on request alongside our agricultural range.
  • Chemical manufacture. Feedstock for zinc sulphate, zinc chloride, zinc stearate, catalysts and desulphurisation sorbents.

Handling and storage

Zinc oxide is very toxic to aquatic life and is transported as UN 3077, Class 9, Packing Group III (environmentally hazardous substance, solid) under the ADG Code; inner packagings of 5 kg or less are exempt under special provision 375. It is a fine powder: use a P2 dust mask and avoid release to drains. Store bags closed and dry; it absorbs carbon dioxide and moisture slowly from air, which raises loss on ignition. Always read the Safety Data Sheet before use.

Why buy Zinc Oxide from UD Trading

Every batch is tested for ZnO content, loss on ignition, lead and cadmium under our ISO 9001:2015 quality system, and we hold stock in multiple Australian warehouses. Browse our general industrial chemicals and agricultural products, or contact our team for a quote. Related products: magnesium oxide, calcium carbonate. Chemical identity reference: CAS 1314-13-2 on CAS Common Chemistry.

Zinc Oxide FAQ

What purity is your zinc oxide?

At least 99.5% ZnO, with loss on ignition ≤ 0.3%, lead ≤ 20 mg/kg and cadmium ≤ 5 mg/kg, reported on the batch COA.

What pack sizes do you supply?

25 kg bags, 1,000 kg pallets of 25 kg bags, jumbo bags and full container loads.

How much zinc is in zinc oxide?

80.3% by mass. One 25 kg bag of 99.5% zinc oxide contains about 20 kg of zinc.

Is zinc oxide dangerous goods?

For transport it is classified UN 3077, Class 9, PG III (environmentally hazardous), except inner packagings of 5 kg or less. It is not flammable or corrosive. Refer to the SDS.

Can it be used in fertiliser and feed?

Yes. The cadmium limit of 5 mg/kg suits fertiliser blends; ask us about feed-grade supply for animal nutrition.

What is the lead time?

It depends on quantity. Smaller orders are dispatched from our warehouses across Australia; larger volumes are scheduled to order; a full container load typically takes 30 to 60 days.

Do you deliver interstate?

Yes. We deliver Australia-wide by road and rail freight, with freight quoted per consignment.

Do you offer contract pricing for scheduled volumes?

Yes. Fixed-period contract pricing is available for scheduled pallet and container quantities.

Product Documents

Download Specification Download SDS

A Certificate of Analysis (COA) is supplied with every batch.

Contact UD Trading for Zinc Oxide

Contact us for pricing, availability and documentation for Zinc Oxide. Call 07 3040 7298 or email sales@udtrading.com.au.

Request a Quote

Ready to Elevate Your Operations?

Connect with our industry experts and unlock your business potential.

Enquire Today

Locations

UD Trading service locations across Australia