Bentonite
UD Trading supplies API 13A drilling-grade sodium bentonite (CAS 1302-78-9) to drilling contractors, water bore drillers, horizontal directional drilling (HDD) crews, mineral explorers, piling and civil contractors across Australia. Our bentonite is a cream to grey powder packed in 1,000 kg bulk bags, dispatched from our warehouses across Australia to Brisbane, Sydney, Melbourne, Perth, Adelaide, Darwin, Roma, Port Hedland and regional drilling centres, with a Certificate of Analysis for every batch under our ISO 9001:2015 quality system.
Bentonite at a glance
| Chemical Name | Bentonite |
|---|---|
| Chemical Formula | Al₂O₃·4(SiO₂)·H₂O (varies by type) |
| Other Names | Montmorillonite Clay, Smectite Clay |
| CAS No | 1302-78-9 |
Pack sizes and how to order
| Pack | Net weight | Typical buyer |
|---|---|---|
| Bulk bag (FIBC, jumbo bag) | 1,000 kg | Drilling contractors, mud plants, piling yards |
| 25 kg bags on pallets | 25 kg (40 per pallet) | Water bore, HDD and exploration crews |
| Full container load (FCL) | 20–24 t | Scheduled contract supply |
Pricing is quoted per order, delivered, usually within one business day of your enquiry. Contract pricing is available for scheduled volumes. Lead time depends on quantity: smaller orders are dispatched from our warehouses across Australia; larger volumes are scheduled to order; full container loads typically take 30 to 60 days. Request a quote or call +61 7 3040 7298.
Bentonite specification
Our bentonite is tested to API 13A Section 9 methods for viscometer reading, yield point to plastic viscosity ratio and filtrate, using a 22.5 g in 350 mL (6.4% w/w) test slurry.
| Parameter | Specification |
|---|---|
| Appearance | Cream to grey powder |
| Viscometer dial reading @ 600 rpm | ≥ 30 |
| Yield point / plastic viscosity ratio | ≤ 3 |
| Filtrate volume | ≤ 15.0 mL |
| Residue > 75 μm (wet sieve) | ≤ 4.0 % |
| Moisture | ≤ 13 % |
Acceptance limits from UD Trading’s approved specification. Actual results for each batch are reported on the Certificate of Analysis.
Physical data: principal mineral sodium montmorillonite; grain density about 2.5 g/cm³; bulk density 800–1,000 kg/m³; swells to 10–15 times its dry volume in fresh water; cation exchange capacity typically 70–100 meq/100 g; a 600 rpm reading of 30 at 6.4% w/w corresponds to a yield of about 90 barrels of 15 cP mud per US ton.
Sodium or calcium bentonite: which one to buy
| Property | Sodium bentonite (this product) | Calcium bentonite |
|---|---|---|
| Swelling in fresh water | 10–15× dry volume | 2–4× dry volume |
| Viscosity at 6% w/w | High; meets API 13A ≥ 30 dial reading | Low; does not meet API drilling grade |
| Filtrate control | Good (≤ 15 mL API filtrate) | Poor |
| Best suited to | Drilling mud, HDD, piling slurry, pond and dam sealing, slurry walls | Foundry sand, pet litter, clarification, some sealing uses |
How much bentonite do you need: worked examples
- Water bore or exploration mud at 5% w/w. 50 kg of bentonite per m³ of water. A 20 m³ mud pit needs 1,000 kg, one bulk bag. Prehydrate for 8–16 hours before adding polymers for full yield.
- HDD drilling fluid at 4–8%. 40–80 kg per m³ depending on ground: 40 kg/m³ in clay, 60–80 kg/m³ in sand and gravel. A 10,000 L mixing tank at 6% takes 600 kg.
- Piling and diaphragm-wall support slurry at 4–6%. Target density 1.03–1.10 g/cm³ and Marsh funnel 32–50 s. A 100 m³ slurry batch at 5% needs 5 t, or 5 bulk bags.
- Treating hard make-up water. Calcium above about 200 mg/L flocculates bentonite and cuts yield. Soda ash precipitates it: Na₂CO₃ + Ca²⁺ → CaCO₃ + 2 Na⁺, so 106 g of soda ash removes 40 g of calcium. Water at 150 mg/L Ca in a 20 m³ pit holds 3 kg of calcium and needs 3 × 106 ÷ 40 ≈ 8 kg of soda ash before the bentonite goes in.
- Pond or dam sealing. Mixed-blanket method at 5–10 kg/m² worked into the top 100–150 mm of soil, depending on soil type and water head. A 1,000 m² farm dam at 8 kg/m² needs 8 t.
What Bentonite is used for
- Drilling mud viscosifier. Bentonite builds viscosity and gel strength to carry cuttings, suspends weighting agents such as barite, and forms a thin, low-permeability filter cake on the borehole wall.
- HDD and trenchless. Stabilises the bore, lubricates the drill string and carries spoil back to the pit; extended with PAC-LV or xanthan gum for fluid loss and suspension.
- Piling, diaphragm walls and slurry trenches. Supports excavations hydrostatically until concrete is placed.
- Pond, dam and landfill sealing. Swelling bentonite blankets and geosynthetic clay liners cut seepage to 10⁻⁹ m/s or lower.
- Civil and industrial. Grouts for monitoring bores and earthing, foundry binder, pelletising and clarification.
Handling and storage
Bentonite is not classified as dangerous goods for transport under the ADG Code. It is a fine, dusty powder: use a P2 dust mask when mixing, and keep bags dry and off the ground, because moisture above the 13% limit causes caking and lowers yield. Lift bulk bags by all four loops. Always read the Safety Data Sheet before use.
Why buy Bentonite from UD Trading
Bentonite that misses its viscometer or filtrate number costs you a slow hole and extra polymer. We release every lot against API 13A limits under our ISO 9001:2015 quality system, hold stock in multiple Australian warehouses, and we are a member of the Australian Drilling Industry Association (ADIA). Browse our drilling fluid chemicals and mining chemicals, or contact our team for a quote. Chemical identity reference: CAS 1302-78-9 on CAS Common Chemistry.
Bentonite FAQ
Is your bentonite API grade?
Yes. It is tested to API 13A Section 9: viscometer dial reading at 600 rpm ≥ 30, yield point to plastic viscosity ratio ≤ 3, filtrate ≤ 15 mL, residue above 75 µm ≤ 4%, moisture ≤ 13%.
How is the bentonite packed?
In 1,000 kg bulk bags as standard; 25 kg bags on pallets are also available, and full container loads can be scheduled.
How much bentonite do I need per cubic metre of water?
40–60 kg/m³ for water bore and exploration muds, 40–80 kg/m³ for HDD, and 40–60 kg/m³ for piling slurry. Prehydrate for 8–16 hours and treat hard water with soda ash first.
Is bentonite dangerous goods?
No. Bentonite is not classified as dangerous goods for transport. Control dust when mixing and refer to the SDS.
Can I use it with salt water or KCl mud?
Sodium bentonite yields poorly in salt water. Prehydrate it in fresh water first, then add salt or potassium chloride, or use a polymer system for saline conditions.
What is the lead time?
It depends on quantity. Smaller orders are dispatched from our warehouses across Australia; larger volumes are scheduled to order; a full container load typically takes 30 to 60 days.
Do you deliver to regional and remote drilling sites?
Yes. We deliver Australia-wide by road and rail freight, including Port Hedland, Dampier, Darwin and inland exploration camps, with freight quoted per consignment.
Do you offer contract pricing for scheduled volumes?
Yes. Fixed-period contract pricing is available for scheduled bulk-bag and container quantities.
Product Documents
Download Specification Download SDSA Certificate of Analysis (COA) is supplied with every batch.
Contact UD Trading for Bentonite
Contact us for pricing, availability and documentation for Bentonite. Call 07 3040 7298 or email sales@udtrading.com.au.

