MEG (Monoethylene Glycol)
UD Trading supplies mono ethylene glycol (MEG) (ethylene glycol, CAS 107-21-1) at 99.9% minimum purity in IBCs and bulk to oil and gas producers and well-service companies, gas processing plants, HVAC and refrigeration contractors, mining and industrial sites, antifreeze and coolant blenders, and resin, polyester and chemical manufacturers across Australia. Orders are dispatched from our warehouses across Australia to Brisbane, Roma, Moomba, Perth, Dampier, Darwin, Sydney, Melbourne, Adelaide and regional centres, with a Certificate of Analysis for every batch under our ISO 9001:2015 quality system.
MEG at a glance
| Chemical Name | Ethylene Glycol |
|---|---|
| Chemical Formula | C2H6O2 |
| Other Names | MEG, Ethane-1,2-diol, Monoethylene Glycol |
| CAS No | 107-21-1 |
Pack sizes and how to order
| Pack | Net quantity | Typical buyer |
|---|---|---|
| 20 L drum | About 22 kg | Trials, laboratories, workshops, small plants |
| HDPE drum | 200 L (about 223 kg) | HVAC contractors, workshops, blenders |
| IBC | 1,000 L (about 1,113 kg) | Gas plants, well-service crews, mines, chiller systems |
| Scheduled contract supply | Monthly volumes | Sites with continuous make-up |
Pricing is quoted per order, delivered, usually within one business day of your enquiry; MEG prices move with crude and ethylene markets, so quotes are held for a stated period. Contract pricing is available for scheduled volumes. Lead time depends on quantity: IBC orders are dispatched from our warehouses across Australia; bulk volumes are scheduled to order; full container loads typically take 30 to 60 days. Request a quote or call +61 7 3040 7298.
MEG specification
Fibre-grade MEG is specified on purity, diethylene glycol, water, colour, iron and acidity. Low water and DEG matter for hydrate inhibition and polyester use; low colour and iron matter for coolants and resins.
| Parameter | Specification |
|---|---|
| Appearance | Clear colourless liquid |
| MEG purity | ≥ 99.9 % |
| Diethylene glycol | ≤ 0.08 % |
| Water | ≤ 0.08 % |
| Colour (APHA) | ≤ 5 |
| Iron (Fe) | ≤ 0.1 mg/kg |
| Acidity (as acetic acid) | ≤ 30 mg/kg |
Acceptance limits from UD Trading’s approved specification. Actual results for each batch are reported on the Certificate of Analysis.
Physical data: molar mass 62.07 g/mol; density 1.113 kg/L at 20 °C; boiling point 197 °C; freezing point −13 °C (pure) falling to −37 °C at 50% v/v in water and about −52 °C at 60%; flash point 111 °C (closed cup), so it is combustible but not a flammable-liquid dangerous good; fully miscible with water; viscosity 16 mPa·s at 25 °C; specific heat of a 50% solution about 3.3 kJ/kg·K against 4.18 for water, so pumps and exchangers need about 25% more flow for the same duty.
MEG, TEG or methanol: which hydrate inhibitor to specify
| Property | MEG (this product) | Methanol | TEG |
|---|---|---|---|
| Main use | Hydrate inhibition in pipelines and wells, regenerable; coolants; antifreeze | Hydrate inhibition where loss to gas phase is acceptable; wellhead injection | Gas dehydration in contactor towers |
| Loss to gas phase | Very low; recovered and regenerated | High; consumed | Low |
| Flammability | Combustible (flash point 111 °C), not DG | Flammable, DG Class 3, toxic | Combustible, not DG |
| Dose for the same suppression | Baseline | About half the mass, but not recovered | Not used for hydrates |
| See also | methanol | On request |
How much MEG do you need: worked examples
- Hydrate inhibition (Hammerschmidt). Hydrate temperature depression ΔT (°C) ≈ 2,335 × W ÷ [62 × (100 − W)], where W is the MEG weight percent in the aqueous phase. For 10 °C of suppression, W ≈ 21%. A well producing 20 m³/day of water needs 0.21 ÷ 0.79 × 20,000 kg = 5,300 kg of MEG a day, about 4.8 kL, most of which is recovered in the regeneration unit. For 15 °C of suppression W rises to about 28.5%.
- Chiller or process coolant at 40% v/v. Freeze protection to about −24 °C and burst protection lower. A 5,000 L closed loop takes 2,000 L (2,230 kg) of MEG plus 3,000 L of water and a corrosion-inhibitor package; two IBCs cover it.
- Antifreeze blending. A 50/50 pre-mix for vehicles and gensets is 500 L of MEG per 1,000 L of product; a 10 kL blending batch needs five IBCs.
- Make-up for glycol loss. Regeneration systems typically lose 0.5–1.5% of circulating MEG per cycle to the gas and brine streams; a plant circulating 50 m³/day loses 250–750 L a day, so plan one IBC every 1.5–4 days.
- Density check for concentration. At 20 °C, 30% v/v MEG reads about 1.040 SG, 40% about 1.055, 50% about 1.070; a hydrometer or refractometer tells you whether the loop needs topping up with glycol or water.
What MEG is used for
- Oil and gas. Hydrate inhibitor injected at wellheads, subsea tie-backs and pipelines, regenerated in MEG reclamation units; heat-transfer fluid in gas plants, alongside our drilling and oilfield chemicals.
- HVAC, refrigeration and mining. Secondary coolant and antifreeze in chillers, cold stores, process cooling and mobile plant.
- Antifreeze and coolant manufacture. Base fluid for automotive, marine and heavy-vehicle coolants.
- Chemicals and polymers. Feedstock for PET and polyester fibre, unsaturated polyester resins and glycol ethers.
- Industrial. Humectant, dewatering agent, hydraulic and de-icing fluids.
Handling and storage
MEG is not classified as dangerous goods for transport, but it is harmful if swallowed and can damage the kidneys with repeated exposure: never siphon by mouth, label containers clearly, keep away from food and animals (it is sweet-tasting and toxic to pets), and clean up spills promptly. Wear gloves and eye protection. Store in sealed HDPE or stainless containers away from heat, oxidisers and strong acids; it is hygroscopic and absorbs water from air, which lowers freeze protection. Always read the Safety Data Sheet before use.
Why buy MEG from UD Trading
Every batch is released against our fibre-grade specification for purity, DEG, water, colour and iron under our ISO 9001:2015 quality system, and we hold stock in multiple Australian warehouses so gas plants and contractors are not waiting on a vessel. Browse our oil and gas chemicals and general industrial chemicals, or contact our team for a quote. Related products: methanol, potassium chloride, calcium chloride. Chemical identity reference: CAS 107-21-1 on CAS Common Chemistry.
MEG FAQ
What grade is your MEG?
Fibre grade, 99.9% minimum purity, DEG ≤ 0.08%, water ≤ 0.08%, colour ≤ 5 APHA, reported on the batch COA.
What pack sizes do you supply?
1,000 L IBCs as standard, 200 L drums, and 20 L drums.
Is MEG dangerous goods?
No. It is not classified as dangerous goods for transport, but it is harmful if swallowed; handle and label accordingly.
How much MEG do I need to stop hydrates?
Use the Hammerschmidt relation: about 21% MEG in the produced water gives 10 °C of hydrate suppression, 28.5% gives 15 °C. We can run the numbers for your water rate and pressure.
What concentration protects a chiller loop?
30% v/v protects to about −15 °C, 40% to about −24 °C and 50% to about −37 °C; add a corrosion inhibitor package for closed loops.
What is the lead time?
IBC orders are dispatched from our warehouses across Australia; bulk volumes are scheduled to order; full container loads typically take 30 to 60 days.
Do you deliver to gas fields and remote sites?
Yes. We deliver Australia-wide by road and rail freight, including Roma, Moomba, Dampier and Darwin, with freight quoted per consignment.
Do you offer contract pricing for scheduled volumes?
Yes. Fixed-period contract pricing is available for scheduled IBC and bulk volumes.
Product Documents
Download Specification Download SDSA Certificate of Analysis (COA) is supplied with every batch.
Contact UD Trading for MEG (Monoethylene Glycol)
Contact us for pricing, availability and documentation for MEG (Monoethylene Glycol). Call 07 3040 7298 or email sales@udtrading.com.au.

